Sortieren nach:   Filter: 
Web Code Artikelnummer Beschreibung Kategorie Preis
16248 EM KNT 002 EINGÄNGE

The interface EM KNT 002 has 4 Analog/Digital independent channels which may
be used depending on the parameterization by the ETS4:
- Binary inputs: it can be connected to a pushbutton, a switch or a conventional
 voltage-free binary sensor .
- Analog inputs: itcan work as temperature sensor by connecting an external
 probe. Then the temperature of the room can be controlled (maximun 4
 temperature sensors).
- Thermostat: It can be configured and enabled 4 independent thermostats.
Each one of the 4 channels can work as:
 - Switch: to turn the light ON and OFF.
 - Switch and Dimmer: to turn ON/OFF and dim the light.
 - Multiple Switch: to turn ON/OFF the light depending on the number of pressings.
 - Sequential Switch: to do sequential switching ON/OFF.
 - Blinds/Shutters Control: to move the blinds/shutter by pushbuttons or switches.
 - Scenes Control: to save and recover a light scene.
 - Values Sending: to send different measures or values, for example the light
 level, temperature,...
 - Impulse Counter: it allows, for example, counting the number of operations.
 - Temperature sensor: sends the temperature value of the room. We can connect
 4 temperature sensors.
 - Thermostat: It can be configured and enabled 4 independent thermostats.
 Furthermore it is independent of the quantity and type of inputs (Analog/Digital)
 are configured.

• 4-channels universal binary/analog interface
• Mounting: behind the pushbutton, inside the universal mechanism box
• Bus supply
• Functions: ON/OFF, Dimming, Blinds control, Scenes control or Temperature control (with external probe)
• Programmation by ETS4:

16248
EM KNT 002 EINGÄNGE
16247 RE KNT 000 AKTOREN
 Universal 1-channel Dimmer for RLC loads
• Load: LED lamps, CFL, Incandescent or Halogen lamps
• Breaking capacity: up to 1.000W with incandescent lamps
• DIN-rail mounting
• Power supply: 230V~
• Programamation by ETS
16247
RE KNT 000 AKTOREN
16462 RE KNT DA1 Schnittstellen
 One-channel modular DALI dimming actutor (up to 64 equipments).
• Protected against overloads and short-circuits. Built-in heating protection.
• Anti-panic input for safety systems.
• Installation in DIN rail.
• Power supply 230V.
• Programinf by ETS
16462
RE KNT DA1 SCHNITTSTELLEN
16249 EM KNT 001 EINGÄNGE
• 4-channels universal pushbutton binary interface
• Mounting: behind the pushbutton, inside the universal mechanism box
• Bus supply
• Functions: ON/OFF, Dimming, Blinds control or Scenes control
• Programmation by ETS:
16249
EM KNT 001 EINGÄNGE
16250 DM KNT 001 IR Motion detector Melder
• IR Motion detector
• Flush ceiling mounting
• Functions: motion detection, constant light control, twilight switch, brigthness & temperature sensor
• Bus supply
• Programmation by ETS
16250
DM KNT 001 IR MOTION DETECTOR MELDER
16252 RE KNT 110 AKTOREN
• One-channel modular 1-10VDC dimming actuator (up to 200 equipments).
• Protected against overloads and short-circuits. Built-in heating protection.
• Anti-panic input for safety systems.
• Installation in DIN rail.
• Power supply 230V.
• Programing by
16252
RE KNT 110 AKTOREN
16246 FA KNT 001 SYSTEMGERÄTE
• Power supply of 640mA , to generate and monitor power Bus EIB / KNX.
• The bus line is isolated from the network by the coil.
• There is a second auxiliary output not isolated from the network.
16246
FA KNT 001 SYSTEMGERÄTE
16251 DM KNT 002 IR Motion detector with constant light control Melder
Wall or surface ceiling mounting KNX motion detector.
It incorporates as main function the motion detection. In addition it is possible to
enable these functions:
 - Twilight switch
 - Constant light control
 - Signal monitoring
 - Brightness sensor
 - Temperature sensor
These additional functions are independent and can or not be enabled.
Wall or surface ceiling mounting, with coverage of 180º and a maximum of 10m in
leght at 2m high.
Possibility of adjusting the delay time and Lux setting by ETS or via control knobs
16251
DM KNT 002 IR MOTION DETECTOR WITH CONSTANT LIGHT CONTROL MELDER
16657 RE KNT RGB AKTOREN

Dimming actuator to control RGBW LED strips .

• It has 4 output channels 16A per channel , with a maximum capacity of 32A.
• Control via KNX PT ( Twisted Pair to 24VDC ).
• Protected against overloads and short-circuits.
• Formato modular, para su instaación sobre carril DIN.
• Anti-panic input for safety systems.
• Programing by ETS4.

16657
RE KNT RGB AKTOREN
16903 CO KNX 002 RF-KNX / KNX- PT media coupler RF
• RF-KNX / KNX- PT media coupler.
• Interface between wireless and twisted-pair devices.
• It allows the transmission of telegrams from the radio modules to KNX Bus devices and vice versa (bidirectional communication).
• Can be used together with devices to control lighting, HVAC, blinds/shutters and main purpose devices.
• Up to 16 bidirectional RF or TP independent channels.
• Power supply: BUS KNX 24VDC.
• Installation in DIN rail.
16903
CO KNX 002 RF-KNX / KNX- PT MEDIA COUPLER RF
18447 IT KNX 001 WIRELESS 1-CHANNEL SWITCH RF
 
It is based on a RF-KNX actuator which emulates the working mode of the channel code
CH_Light_Actuator_Scene 0x103.
It is composed by: LED (A), Time Selector (B), Commissioning Pushbutton (C) and
Working Mode Selector Switch (D).
 
CHARACTERISTICS
Working mode selector switch for the setting-up and commissioning:
- B: delete a link from the receiver channel.
- P: link programming of the transmitter or receiver channel.
- F: normal operation.
- A: normal operation with repeater function.
- R: delete all links from the transmitter and receiver channels.
Operation as impulse relay or time switch.
Possibility of working as RF signals repeater.
Possibility of wiring an additional wired pushbutton to:
- Local control of the load connected to the device.
- Remote control, via RF, of one or several linked receivers.
Compatible with ISO-IEC 14543-2 KNX protocol. Two objects:
- The auxiliary pushbutton answers to the object CH_PB_Toggle 0x02.
- The actuator answers to the object CH_Light_Actuator_Scene 0x103
18447
IT KNX 001 WIRELESS 1-CHANNEL SWITCH RF
18448 PE KNX 001 AKTOREN

Wireless actuator for switching or controlling blinds/shutters compatible with the

KNX-RF Standard.

It has 2 output channels which allow to control one blind/shutter or to use them as a two channels switching (ON/OFF) actuator.

It has 2 auxiliary inputs which allow to control also by two wired conventional pushbuttons.

MOUNTING AND INSTALLATION

A. Mounting:

· Place the actuator with the antenna as faraway as possible from wires or metallic surfaces.

· Move away the actuator from attenuations or interferences, for example from metallic surfaces or other radio-frequency devices.

B. Installation:

Important: Switch off the power supply when installing.

B.1. - Wiring as 1-channel blinds/shutters actuator

To roll up or down a blind, follow the wiring diagram of Fig 1.

Allows the connection of 2 wired buttons (P1 and P2), which permit the possibility

of controlling the load with two wired pushbuttons.

B.2. - Wiring as 2-channels switching actuator

To control the switching ON and OFF of two diferent loads follow the wiring diagram

of Fig 2.

Allows the connection of 2 wired buttons (P1 and P2), which permit the possibility

of controlling the load with two wired pushbuttons.

 

18448
PE KNX 001 AKTOREN
18449 TM KNX 001 RF

Wireless modular thermostat that allows controlling the air conditioning system using wireless

sensors: temperature sensor, door/windows contact or presence detector.

It can be fixed a certain temperature and connect or disconnect the heater or the air conditioning

according to different parameters: temperature measured by an external sensor, the opening or

closing of door/window or the presence of people in the room.

By default, after the commissioning is considered an ambient temperature of 25°C. Not receiving

a different value from some associated temperature sensor, it will be considered at all times that

initial temperature is maintained.

DIN-rail mounting. It allows its installation in cabinets, out of the reach of unauthorized persons.

Working mode selector switch for the setting-up and commissioning:

 - B: delete a link from the receiver channel.

 - P: link programming of the transmitter or receiver channel.

 - F: normal operation.

 - A: normal operation with repeater function.

 - R: delete all links from the transmitter and receiver channels.

Compatible with ISO-IEC14543-2 KNX protocol. One object: CH_Room_Regulator_Type_0B 0x512h

18449
TM KNX 001 RF
18450 RE KNX LE1 AKTOREN
· It is a wireless universal dimmer compatible with the KNX-RF protocol for the control of
dimmable LED lamps, incandescent and halogen lamps.
· Leading (L1) or Trailing (L2) edge dimming technology, depending on the position of the
selector switch (C) and the load.
· Protected against overloads and shortcircuits.
· Control by any RF-KNX sensor: pushbutton, remote control...
· Compatible with DINUY?s sensors: RC KNX 001, PU KNX 001 and EM KNX 002.
· Possibility of control through wired pushbutton (D).
· Incorporates the Momory functional (optional).
 
CHARACTERISTICS
Working mode selector switch for the setting-up and commissioning (A):
- P: link programming.
- R: standard operation with repeater function.
- S: standard operation.
- E: one link deletion from the receiver channel.
- EA: all links deletion from the receiver and transmitter channels.
Load type selector switch (C). It has 2 functions:
- 1º. Select the load type:
· L1: 230V~ LED lamps and 12V~ halogen lamps with ferromagnetic transformer.
· L2: 12V~ LED lamps with electronic transformer, Incandescent & Halogen lamps and
12V~ Halogen lamps with electronic transformer.
- 2º. Select the minimum lighting level (- +). It is useful with LED lamps. It avoids undesirable
effects (e.g.: blinks) when the LED lamps are dimmed at low level.
It has a Programming key (A) for linking other RF devices.
It is possible to wire an auxiliary pushbutton (D) for the local control of the load: switch on/off and dimming. Lighting pushbuttons are not alowed.
Two RF channels: output channel (wired pushbutton) and input channel (of the dimmer)
18450
RE KNX LE1 AKTOREN
18451 RE KNX LE3 AKTOREN
 It is a wireless dimmer compatible with the RF-KNX protocol for the control of 12~48VDC onecolour LED strips, up to 4A.
· Supports the following telegrams: On, Off, Timed On, Scene, Relative Dimming and Absolute Dimming.
· Pulse Width Modulation dimming technology (PWM).
· Control by any RF-KNX sensor: pushbutton, remote control,...
· Compatible with DINUY?s sensors: RC KNX 001, PU KNX 001 y EM KNX 002.
CHARACTERISTICS
Working mode selector switch for the setting-up and commissioning (A):
 - P: link programming.
 - R: standard operation with repeater function.
 - F: standard operation.
 - E: one link deletion from the receiver channel.
 - EA: all links deletion from the receiver and transmitter channels.
 
With or without Memory working modes (B).
It has a Programming key (C) for linking other RF devices.
 
INSTALLATION Install the actuator according to the shown wiring diagram.
18451
RE KNX LE3 AKTOREN
18452 RE KNX RGB AKTOREN
· It is a wireless dimmer compatible with the RF-KNX protocol for the control of 12~48VDC RGB
 LED strips, up to 5A per channel.
· Pulse Width Modulation dimming technology (PWM).
· It has 3 output physical channels (R, G and B) and 4 working channels (R + G + B). The fourth
 channel allows to control the 3 RGB channels at the same time.
· It has a control knob (B) which allows selecting the desired working mode.
· A second control knob (A) allows to select the channel to be linked or deleted at the time of
 commissioning:
- 1: Channel R.
- 2: Channel G.
- 3: Channel B.
- 4: Channel R+G+B.
· Control by any RF-KNX sensor: pushbutton, remote control,...
· Compatible with DINUY?s sensors: RC KNX 001, PU KNX 001 y EM KNX 002
18452
RE KNX RGB AKTOREN
18454 RE KNX 010 Wireless controller, compatible with KNX-RF protocol, for control of luminaires, fluorescence or LED, with reactance or driver adjustable by signal 1 / 10Vcc. AKTOREN
• Wireless controller, compatible with KNX-RF protocol, for control of luminaires, fluorescence or LED, with reactance or driver adjustable by signal 1 / 10Vcc.

• Control via wireless RF transmitter and / or conventional wired pushbutton: short presses on / off, maintained pulses regulate.

• Memory function

• Recessed mounting in registration box

• Incorporates relay output for the physical disconnection of luminaires.

• Possibility of adjusting the speed of regulation by potentiometer
18454
RE KNX 010 WIRELESS CONTROLLER, COMPATIBLE WITH KNX-RF PROTOCOL, FOR CONTROL OF LUMINAIRES, FLUORESCENCE OR LED, WITH REACTANCE OR DRIVER ADJUSTABLE BY SIGNAL 1 / 10VCC. AKTOREN
18895 CO KNT 002 USB / KNX-PT Kommunikationsschnittstelle SYSTEMGERÄTE
• Ermöglicht den Aufbau einer bidirektionalen Verbindung zwischen einem PC und dem Bus der KNX-Installation
• Der USB-Anschluss hat eine galvanische Trennung des KNX-Busses
• Diese Schnittstelle ist kompatibel mit ETS 3 oder höher.
18895
CO KNT 002 USB / KNX-PT KOMMUNIKATIONSSCHNITTSTELLE SYSTEMGERÄTE
16253 ST KNT 001 SENSOREN
ST KNT 001: 
• NTC temperature probe for EM KNT 002 sensor.
• Probe length: 3 meters.
16253
ST KNT 001 SENSOREN
16428 EM KNX 002 RF

 

16428
EM KNX 002 RF
16429 PU KNX 001 PORTABLE 1-CHANNEL WIRELESS PUSHBUTTON RF
• 1-channel portable pushbutton
• Functions: ON/OFF, dimming or save/recover 1 scene
• Installation: surface mounting or portable
• Power supply: battery-operated
• Radio-frequency: 868,4MHz
• Range: 100m (in the free field)
16429
PU KNX 001 PORTABLE 1-CHANNEL WIRELESS PUSHBUTTON RF
16430 RC KNX 001 5-CHANNELS REMOTE CONTROL RF
• 5-channels remote control
• Function: ON/OFF/Dimming the lighting, move up/dpwn blinds or shutters, save/recover 5 scenes
• Power supply: battery-operated
• Radio-frequency: 868,4MHz
• Range: 100m (in the free field)
16430
RC KNX 001 5-CHANNELS REMOTE CONTROL RF
16431 AM KNX 001 RF SIGNALS REPEATER RF
• RF signals repeater
• Function: repeat wireless signals in order to reach longer ranges
• Power supply: battery-operated
• Radio-frequency: 868,4MHz
• Range: 100m (in the free field)
16431
AM KNX 001 RF SIGNALS REPEATER RF
16432 SE KNX 001 WIRELESS TEMPERATURE SENSOR KEINE PRODUKTKATEGORIE
• Temperature sensor
• Function: sends the temperature of the room periodically
• Installation: surface mounting
• Power supply: battery-operated
• Radio-frequency: 868,4MHz
• Range: 100m (in the free field)
16432
SE KNX 001 WIRELESS TEMPERATURE SENSOR KEINE PRODUKTKATEGORIE
16433 SE KNX 002 WIRELESS BRIGHTNESS SENSOR RF
• Brightness sensor
• Function: solar protection
• Installation: glued on the window
• Power supply: battery-operated
• Radio-frequency: 868,4MHz
• Range: 100m (in the free field)
16433
SE KNX 002 WIRELESS BRIGHTNESS SENSOR RF
16434 SE KNX 003 WIRELESS DOORS/WINDOWS CONTACT RF
• Door/window contact sensor
• Function: detects if the door or window is openned and sends the respective telegram
• Power supply: battery-operated
• Radio-frequency: 868,4MHz
• Range: 100m (in the free field)
16434
SE KNX 003 WIRELESS DOORS/WINDOWS CONTACT RF
16435 SE KNX 004 WIRELESS TEMPERATURE SENSOR & THERMOSTAT RF
• Temperature sensor with temperature setting
• Function: sends the ON or OFF telegram depending on the temperatura of the room and the set one
• Installation: surface mounting
• Power supply: battery-operated
• Radio-frequency: 868,4MHz
• Range: 100m (in the free field)
16435
SE KNX 004 WIRELESS TEMPERATURE SENSOR & THERMOSTAT RF
16442 SE KNX 005 WIRELES TEMPERATURE SENSOR WITH PROBE RF
• Temperature sensor with Probe
• Function: sends the temperature measured by the probe
• power supply: 230V~
• Radio-frequency: 868,4MHz
• Range: 100m (in the free field)
16442
SE KNX 005 WIRELES TEMPERATURE SENSOR WITH PROBE RF
16443 DM KNX 001 FLUSH-CEILING MOUNTING MOTION DETECTOR RF
• Flush-ceiling mounted IR motion detector
• Function: as soon as it detects movement it sends an ON signal to the linked actuator and keeps its contact closed for the time set on the actuator. With each detection the sensor sends the telegram to the actuator and restart the delay time
• Coverage: Ø6m at 2.4m high
• Mounting: flush-ceiling
• Power supply: battery-operated
• Radio-frequency: 868,4MHz
• Range: 100m (in the free field)
16443
DM KNX 001 FLUSH-CEILING MOUNTING MOTION DETECTOR RF
16444 DM KNX 002 SURFACE-MOUNTING MOTION DETECTOR RF
• Surface mounted IR motion detector
• Function: as soon as it detects movement it sends an ON signal to the linked actuator and keeps its contact closed for the time set on the actuator. With each detection the sensor sends the telegram to the actuator and restart the delay time
• Coverage: 180º and 10m
• Mounting: wall or ceiling
• Power supply: battery-operated
• Radio-frequency: 868,4MHz
• Range: 100m (in the free field)
16444
DM KNX 002 SURFACE-MOUNTING MOTION DETECTOR RF
16929 ST KNT 002 Temperature probe, Epoxi black, 0.5m SENSOREN
• Sondas de Temperatura Epoxy NTC para el sensor de 4 entradas binarias/analógicas EM KNT 002.
• Medición por contacto o del aire que le rodea.
• Gran precisión y estabilidad sobre un amplio rango de temperatura.
• Se incluye un cable de 3m (ST KNT 001) o de 0,5m (ST KNT 002) de longitud.
16929
ST KNT 002 TEMPERATURE PROBE, EPOXI BLACK, 0.5M SENSOREN
19052 PU KNT 029 Laüka Capacitive push buttons White glass + wooden frame Tasterschnittstellen

LAÜKA
• KNX multifunctional capacitive pushbuttons
• Full control over the lighting, the blinds and to be able to memorize desired scenes
• Designed for diversity of facility types
• Glass touch surface
• Option of 4 or 8 push buttons
19052
PU KNT 029 LAÜKA CAPACITIVE PUSH BUTTONS WHITE GLASS + WOODEN FRAME TASTERSCHNITTSTELLEN


SPEZIELLE KNX KATALOGE
360°-Ansichten
Tastsensoren
Smart Metering

SCHULUNGEN
Kostenlose Webinars
uBrick- Aktoren
Videoschulung CBSE

MITMACHEN
µBrick Trivia
ONLINE-TESTS
Kostenloser Test der CBSE Visualisierung

JÜNGSTE KNX NEWS
Alle News

JÜNGSTE KNX ANGEBOTE
Alle Angebote
DOWNLOADS
KNX - Alle Marken

FUTURASMUS KNX GROUP
Kontakt
Niederlassungen
Futurasmus weltweit
FOLLOW US
YouTube Channel
Facebook
LinkedIN
Google+
Twitter

KNX++ SCHULUNGSSTÄTTE
Futurasmus Zentrum

ZERTIFIZIERTE KNX TEST LAB
Futurasmus KNX Lab
SPEZIALISIERTER KNX GROßHANDEL ZERTIFIZIERTE KNX AUSBILDUNGSSTÄTTE
Die Futurasmus KNX Group ist ein hoch spezialisierter und international tätiger KNX-Fachgroßhandel mit einem umfangreichen technischen Support über alle Produkte. Wenn Sie unseren Online-Katalog durchblättern, können Sie sich als Professional (Gewerbe und Wiederverkäufer) ein unverbindliches Angebot erstellen lassen. Wenn Sie KNX-Produkte kaufen möchten, kontaktieren Sie bitte unsere kaufmännischen oder technichen Ansprechpartner per Telefon, E-Mail oder Online-Chat. Unsere AGBs finden Sie hier. Unsere Zulassung als KNX++ Ausbildungsstätte im Jahr 2003 ermöglicht uns seither nicht nur den KNX-Grundkurs, sondern auch die Kurse für Fortgeschrittene und Ausbilder anzubieten. Wir schulen herstellerunabhängig und bieten auch andere fachspezifiesche KNX Schulungen an. Nach über 1.500 erfolgreichen Absolventen verfügen unsere Ausbilder über einen fundierten, umfangreichen und positiven Erfahrungsschatz im Bezug auf die KNX-Ausbildung. Wenn Sie Interesse an einer auf Sie angepassten KNX Schulung haben (min. 8 Personen), melden Sie sich einfach bei uns unter training@futurasmus-knxgroup.org
HINWEIS ZU COOKIES
Wir nutzen eigene und sog. Third-Party Cookies, um die Benutzung unserer Website zu analysieren. Ebenso verbessern wir dadurch die Sicherheitsmaßnahmen, die Qualität und unsere Dienste für unsere Nutzer. Wenn der Nutzer sich zur Installation von Cookies nicht äußert und unsere Website weiter benutzt, stimmt er ausdrüclich der Verwendung der Cookies zu. Es bleibt ihm frei, sich über die Behandlung von Cookies, insbesonderes für die notwendigen Einstellungen bei den jeweils genutzten Web-Browsern, zu Informieren. Weitere Informationen erhalten Sie bei unseren "Cookies Policy".